Buy ASTM D TEST METHOD FOR OPEN CELL CONTENT OF RIGID CELLULAR PLASTICS from SAI Global. (ASTM D) Standard Test Method for Open Cell Content of Rigid Cellular Plastics [Gas Pycnometer] – This test method determines numerical values for open. DIFFERENT APPLICATIONS: Correction For Cut Cells. In ASTM D, a corrected percentage of open cells is estimated by remeasuring the volume of a cube.
|Published (Last):||12 October 2013|
|PDF File Size:||4.12 Mb|
|ePub File Size:||2.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D6226-05 standard open cell content of rigid cellular plastics
For the best results, we recommend including the following details: The difference adtm the two pressure combined with the known volume of the empty sample chamber allows the volume of the sample to be determined by way of the gas law.
Proceed to Checkout Continue Shopping. When the pressure has fallen to less than 3 kPa [0. I would like your verified suppliers matching service! NOTE 5—The cylindrical conguration is not recommended for anisotropic materials. Summary of Test Method 4. The valve alternative means to vent the gas. It is obtained by pooling the within-laboratory astn deviations of the test results from all of the participating laboratories. Originally approved in The remaining volume is that occupied by closed cells and cell walls.
Chairman Subcommittee D An alternative conguration is two cylinders with nominal cross sectional areas of 6. Or if two cylinders: Summary of Test Method 4. If using cylindrical specimens asm the height, h, and diameter, d.
Precision, characterized by repeatability Sr and r and reproducibility SR and R have been determined as shown in Table 1. NOTE 6—It will be desirable in some instances to use pressures less than 20 kPa for the purging and testing steps. If a shift occurs, repeat 9.
Link to Active This link will always route to the current Active version of the standard.
ASTM D – 15 Standard Test Method for Open Cell Content of Rigid Cellular Plastics
V V shift from zero. The valve between the two chambers is then opened and the second, lower Pressure, P2, is again noted.
If there are no material specifications, then the default conditions apply. View our resource center to find press releases, testimonies, infographics and more. As the voice of the U. P2 is the resulting intermediate pressure. Apply to research and quality control for below materials: Signicance and Use 5. It may xstm practical in some instances for example, when using smaller sized sample 6.
Since any conveniently ume Percentage of Open and Closed Cells of Rigid Materials5 sized specimen can only be obtained by some cutting opera- tion, a fraction of the closed cells will be opened by specimen 3. Record these volumes on the data d62226 along with the ID of the instrument, the date and ID of the operator. Any test specimen preparation, conditioning, or dimensions, or both, and testing parameters covered in the materials specication v6226 take precedence over those mentioned in this test method.
Send your message to this supplier.
It is a porosity determination, measuring the accessible cellular volume of a material. This d626 process shall be repeated at least twice more. By not accounting for closed cells that were opened during specimen preparation, the accuracy decreases as the closed cell content increases and as the cell size wstm.
A greatly simplied diagram of the instrument is shown in Fig. By not accounting for closed cells that were opened during astk preparation, the accuracy decreases as the closed cell content increases and as the cell size increases. If there are no material specications, then the default conditions apply. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Report the time used if the pressure did not stabilize. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Active Member 6 Years. A superscript epsilon e indicates an editorial change since the last c6226 or reapproval. Last previous edition approved in as D – 98e1. Enter your email please. Terminology preparation and will be included as open cells, see Note 2. It is possible that it will be practical in some instances for example, when using smallersized sample chambers or when there is a limited amount of material to use only one cube or one cylinder. D62226 volume occupied by closed cells is considered to include cell walls.
The remaining volume is that occupied by closed cells and cell walls. These cells may be interconnecting open cellnon-connecting closed cell sstm, or any combination of these types. It shall have the following features: